buzzbomb Posted January 9, 2016 Report Share Posted January 9, 2016 I'm so cheap and lazy that if I was going to consider them disposable or near as, I might take the path of least resistance and just drill in 1/8" or so and glue in a swivel, (cheap or otherwise). For distance you might gain a bit by trimming the stone with a tile saw or chop saw or grinder and vise to make it more aerodynamic but be careful, it's all good fun until someone loses an eye. I'm curious about just what it takes to drill into or through stones as I have a drill press and vise in the basement, and like the notion of in-lines as well. Quote Link to comment Share on other sites More sharing options...
gagnaccarp Posted January 9, 2016 Author Report Share Posted January 9, 2016 I drilled all holes with a bog standard masonry drill bit , to make the bigger hole I started off with a 6 mm drill bit then used a 8 mm then 10 mm then 12 mm , I will look at both methods , glue in swivel and the hole through . ! the soft sandstone I drill is quite soft , I just hold the stone in my left hand and drill with my right hand with the stone resting on a wooden bench or something that doesn't matter if it gets drilled ,my drill is light though , might be tricky with a heavier drill ! Quote Link to comment Share on other sites More sharing options...
theloneangler Posted March 2, 2016 Report Share Posted March 2, 2016 Very interesting this i do something similar with stones just make them in to a traditional style lead and use the lead clip to drop them like you would any normal lead But does take the time making the stones in weights but can save a fair bit of money nealjt 1 Quote Link to comment Share on other sites More sharing options...
gagnaccarp Posted March 2, 2016 Author Report Share Posted March 2, 2016 CM , what about clay , where I fish its easy to get hold of a bit of clay , is with a lot of waters , I haven't looked at Chillys drop off , how old is it ? nealjt 1 Quote Link to comment Share on other sites More sharing options...
gagnaccarp Posted March 2, 2016 Author Report Share Posted March 2, 2016 yep , found them , people also use a staple to make back leads ! nealjt 1 Quote Link to comment Share on other sites More sharing options...
gagnaccarp Posted March 2, 2016 Author Report Share Posted March 2, 2016 Yep , I will give it a bash , there are a few places where I need to " hold bottom " in the flow where I'm going to use around 4 - 10 oz pebbles , easy = good , and it doesn't get much easier than wrapping a bit of plasticine round your swivel ! nealjt 1 Quote Link to comment Share on other sites More sharing options...
nealjt Posted March 2, 2016 Report Share Posted March 2, 2016 Nice !!! You could mould oils/ flavours into plasticine also Quote Link to comment Share on other sites More sharing options...
spr1985 Posted March 2, 2016 Report Share Posted March 2, 2016 With the plasticine do you use it in its malleable form or bake it so it sets hard? Quote Link to comment Share on other sites More sharing options...
salokcinnodrog Posted March 2, 2016 Report Share Posted March 2, 2016 I used to use plasticine as a weight for chub fishing, moulded around the line or as a drop off weight moulded around a couple of shot on a paternoster link. After time it sets solid in the tackle box, and no amount of kneading will make it go soft again, so some blocks had a loop of line pushed through them. Quote Link to comment Share on other sites More sharing options...
spr1985 Posted March 2, 2016 Report Share Posted March 2, 2016 I was maybe thinking of play dough I remember when I was at school making it into shapes and teachers baking it to set it rock solid.... Quote Link to comment Share on other sites More sharing options...
spr1985 Posted March 2, 2016 Report Share Posted March 2, 2016 I was merely asking a question, I don't need it solid or malleable but...... as the thread is about a drop off pebble which is solid I thought maybe a an alternative cheap material instead of pebbles Quote Link to comment Share on other sites More sharing options...
salokcinnodrog Posted March 2, 2016 Report Share Posted March 2, 2016 That would defeat the object Nick, i need it to come off, anything forcing the fishes head down or snagging in the lilies means a lost fish, it may suit guys long casting but its not what i use it for, another option maybe. The loop does pull out when it snags up, which is why I still use it. A short length of Amnesia pushed in and through, with the ends lighter blobbed to stop them pulling out on the cast, but allowing it to pull out on any tension or snagging Quote Link to comment Share on other sites More sharing options...
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.